Infiniti FX Forum banner

1 - 17 of 17 Posts

·
Premium Member
Joined
·
73 Posts
Discussion Starter #1
DIY -2nd Gen Front Bumper Removal + AC Condenser Coil Guard Install

Skill: Medium
Time: 2 - 4 Hours


Half way through the return leg of a long road trip early last December, my AC began to blow warm air. I pulled over at a rest stop and looked under the car and discovered that my AC Condenser was leaking refrigerant all over the lower inner bumper. I drove the car to the dealer the very next morning and they confirmed that road debris had punctured my condenser coils. Unfortunately this was not covered under warranty and they wanted $950 + tax to complete the repair.

After much research I found that this was a common occurrence across all car manufacturers. I found a few threads on pending class action lawsuits against Honda and Toyota for inadequate protection of the fragile AC condenser given the close proximity to the road. I also came across complaints about previous generations of Infiniti's having similar issues as well. It seems the exposed coils are a design oversight.

After some "creative bargaining" and a "friendly" discussion with the Infiniti Master Mechanic and SA about lower grill designs, they decided to do a Goodwill service and I agreed to pay for half the labor totaling $130.

I do a ton of road trips in my FX and did not want to go through this headache again, so I decided to be a little proactive and build my own condenser guard. I came across a number of posts where people have devised their own AC coolant guards, and in one case Toyota addresses the problem with a TSB (see reference links section). Infiniti has also wised up as the more recent models have a Honeycomb grills in the lower bumper. Hopefully they will apply this to future FX's.

As an alternative, you could replace the condenser coil yourself if it ruptures and take your car to an AC specialist to have them recharge the system for a nominal fee, but I would rather just have it protected in the first place. It sucks not having AC on a long road trip...especially when driving through Florida.

Initial Concerns:

1) Reduced airflow leading to overheating - ( I've confirmed that this is a none issue. It has been two months since installation, and the temp is at the same level it was before the mod)
2) Rattle/Noise - so far so good no noise from that area. Install is solid and holding.
3) Aesthetically pleasing - Judge for yourself, I like how it turned out.

Items needed:
- Review and print attached service manual pages -EXT 12 - 15, 31 - 33 (attached below)
- Moving Blanket ( to lay the bumper down on.)
- An extra set of hands ( to help hold the bumper when removing/installing. (I managed to do it alone because I am strong like that ;))
- GROMMET - 76881-JG00A -$2.99 ( I broke one of these holding the trim because the plastic clip had pretty much crystallized and fell apart when I removed it)
- Commercial Electric Mounting Ties - Military rated for outdoor/high temperature use and UV Resistant. (Home Depot)
- Commercial Electric Mounting Base - Military rated for outdoor/high temperature use and UV Resistant with Adhesive-backing. (Home Depot)
- Metal Grill - Description "2.5 REG METAL LATH - B 722-000", should be enough to do two cars. (Homedepot $6.98)
- Black Plastic dip or paint spray - (to blend with the car and give it a factory appearance.) (Lowes, HomeDepot - $4)
- Mechanics Gloves ( because you WILL cut your fingers on the grill without these, trust me).

Tools:
-Automotive Trim Pry Bars (Harbor Freight - $6)
-Sheet Metal Cutters
-Pliers
-Wire cutters
-Screwdrivers - (you will need a Shorty Phillips and regular Phillips)
-10mm Socket wrench
-Flashlight

Lots of patience and a beverage.
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #2
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

EXT-33 Bumper Removal - pt.4
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #3
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Steps: 1 of 8

1.) Paint the Grill with Plastic Dip.

- In a well ventilated area put down a drop cloth/plastic/newspaper.
- Lay the grill on something raised so the plastic dip won't dry and stick to drop paper below.
- Measure out the area you want to protect and add a few inch's then tape or mark off this area on the grill.
- Spray each area with two or more coats following the directions for drying time between each coat.
- I left mine to dry overnight.
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #4
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 2 of 8

2.) Remove Bumper: Review and print attached service manual pages -EXT 12 - 15, 31 - 33

a) Using tape on the bumper mark the area where the Adaptive Cruise sensor is located (If so equipped).
-see attached Pictures for clarification.

-Pay special attention to the left connectors for the fog lamps and front camera (if so equipped) and disconnect these.
-Remove right side fog light bulb or connector.
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #5
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 2 of 8 - continued..
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #6
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 2 of 8 - continued..
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #7
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 2 of 8 - continued..
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #9
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 3 - 6

Fabricating grill:

3.) Cut and mold metal grill to shape around the lower and upper bumper openings.
- Upper opening - trim all excess metal (outlined in red on the photos) as the clearance is small when putting the bumper back on.
- Lower opening - the corners need to be trimmed tightly (outlined in red on the photos) as there is limited clearance between the fog lamp and water barriers.

4.) Clean area around the lower bumper opening with denatured alcohol or some kind of degreaser to remove all the road grime/oil e.t.c. and make certain the area is dry when complete.

5.) Lower opening only (Place Zip tie mounts about 3 - 4 inches apart all around the opening and zip tie the grill in place as snug as possible but not overly tight to distort the metal)

6.) Upper opening only (the grill is held in place by the bolts holding the chrome wave grill in place.
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #10
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 3 - 6 continued...
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #11
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Step 7 - 8

7.) When putting the bumper back on pay special attention to the openings. If you have to push too hard there may be too much metal in the way, pull the bumper back off and trim the excess using the red outlines in the photo as a guide until the bumper goes on without much force. [attachment=0:6k3obfn3]Removebumper15A.jpg[/attachment:6k3obfn3]

8.) Trim opening for tow hook.
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #12
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Finished Product:
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #13
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

More of the Finished product.
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #14
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Reference Links.

Zip Tie Method - http://www.9thgencivic.com/forum/attach ... g_0794.jpg

Gutter Guard Method - http://www.8thcivic.com/forums/do-yours ... enser.html

Toyota TSB - CONDENSER DAMAGE DUE TO ROAD DEBRIS – AC002-06 - http://tinyurl.com/ToyotaTSB

Hardware Cloth Method - http://www.8thcivic.com/forums/attachme ... mbined.jpg

Jeep Mesh Mod - http://www.tmar.net/mesh-grill-mod-jk-jeep-wrangler.htm

Another Gutter Guard method - http://tinyurl.com/7j77d7w
 

·
Premium Member
Joined
·
73 Posts
Discussion Starter #15
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Missing Service manual pages.

Pages

-EXT -12
-EXT -31
-EXT -32
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #16
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

- How to unplug the Fog lamp/Camera connector. This was a pain with the cram quarters in the bumper area. Hopefully this image will make it easier.[attachment=0:k5afq2x6]Removebumper10A.jpg[/attachment:k5afq2x6]
 

Attachments

·
Premium Member
Joined
·
73 Posts
Discussion Starter #17
Re: DIY -2nd Gen Front Bumper removal + AC Condenser Coil Gu

Given the times we live in I must say you are free to use this advice as you see fit. I accept no liability for anything that may happen to you, your FX, your dog or anyone for that matter from using this information. I hope this information proves useful to someone.
 
1 - 17 of 17 Posts
Top