How to Program Homelink - Infiniti FX Forum : FX35, FX45 and FX50 Forums
 
LinkBack Thread Tools
post #1 of 2 (permalink) Old 10-23-2009, 12:26 PM Thread Starter
Senior Member
 
Join Date: Oct 2005
Location: Long Island, New York
Posts: 1,278
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Send a message via AIM to da mayor
How to Program Homelink

Here is the directions:
NOTE: Some vehicles may require the ignition to be turned on or to the second (or accessory or ACC) position for training and/or operation of HomeLink. It is also recommended that a new battery be replaced in the hand held transmitter of the device being trained to HomeLink for quicker training and accurate transmission of the radio frequency.1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)
2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface (located on your mirror), keeping the HomeLink indicator light in view.

3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.) Note: Some garage door openers may require you to replace step 3 with the cycling procedure noted in the View Canadian Instructions section.

4. Press and hold the trained HomeLink button and observe the indicator light.If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.

5. At the garage door opener receiver (motorhead unit) in the garage, locate the learn or smart button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door openers manual or contact us.
6. Press and release the learn or smart button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, there are 30 seconds in which to initiate the next step.
7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the press/hold/release sequence up to 3 times to complete the training process. HomeLink should now activate your device.Retain the original hand-held transmitter of the RF device you are programming for use in other vehicles, as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes. To erase the programmed buttons, perform the procedure shown in step number 1.**To train additional HomeLink buttons, begin with step two.

[Kenny Chan] Finance Manager @ INFINITI of Massapequa (facebook: facebook.com/kennyatinfiniti Twitter: ItsMeDaMayor)
da mayor is offline  
Sponsored Links
Advertisement
 
post #2 of 2 (permalink) Old 04-04-2010, 04:01 PM
Senior Member
 
sirtrojan's Avatar
 
Join Date: Jun 2009
Location: Warsaw /Poland/ EU
Posts: 204
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Re: How to Program Homelink

Does it work for II gen?

- regards - Greg from Poland
SOLD FX35 '06 Brillant Silver/Black |Tech | Sport | Touring | Hands-free Package | 20" rims | CAI STILLEN | Z-TUBE |MOTORDYNE 5/16 Plenum Spacer | Gianelle Spidero 20" + TOYO 295/45/20 |
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Admin
|
sirtrojan is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Infiniti FX Forum : FX35, FX45 and FX50 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










User Tag List

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



  Similar Threads
Thread Thread Starter Forum Replies Last Post
Homelink to Homelink is it possible? RACER-X General Chat 10 02-07-2009 10:22 AM
Proximity Upgrade for Homelink ITSecGuy Internal and External 0 12-19-2007 01:23 PM
//////////Where can I get the NAVIGATION PROGRAM CD??/////// ageshi Audio / Video / Navigation / Electronics 2 11-26-2007 12:56 AM
Interesting Homelink programming dilema krzys4 1st Gen (2003-2008) 10 05-03-2005 11:39 AM
Can somebody post the procedure for Homelink programming? MustGoFastR 1st Gen 8 04-06-2005 06:19 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome